dbl adb selection

2017-04-13 09:37:41   0  举报





仅支持查看

”dbl adb selection” 是一个在Android设备上进行ADB（Android Debug Bridge）操作的命令。这个命令主要用于选择要控制的设备或者模拟器实例。在执行其他ADB命令之前，必须先使用此命令选择一个目标设备。如果未指定任何参数，那么该命令将列出所有已连接的设备或模拟器。此外，还可以使用一些选项来过滤设备的列表，例如只显示正在运行的设备等。总的来说，”dbl adb selection” 是一个非常实用的命令，它使得ADB操作更加方便和高效。

作者其他创作

大纲/内容

L_DBL_active = 0L_LS_active = 1

L_DBL_active

power on or reset

HB_mode == 0&&LS_L_mode == 1&&L_MW_Oncoming == 0

(HiBeamatic_active == 1&&HighBeamStatus ==0&&ADB_City ==0&&ADBLeftprState ==3)||HighBeamStatus ==1

L_MW_Oncoming

HiBeamatic_active

(HiBeamatic_active == 0&&HighBeamStatus==0&&LS_L_enable ==0

HB_L_mode = 0LS_L_mode = 1

L_DBL_active = 1L_LS_active = 0

LS_L_enable

(HiBeamatic_active == 0&&HighBeamStatus ==0&&ADBLeftprState !=3)&&LS_L_enable ==0

HiBeamatic

Cam_ObjNum

L_LS_active

HB_mode == 0&&LS_L_mode == 1

LS_activation_condition

HB_mode == 0&& (LS_L_mode == 0 || L_MW_Oncoming == 1)

LS_L_mode

(HiBeamatic_active == 0&&HighBeamStatus ==0&&ADBLeftprState ==3)&&LS_L_enable ==1

HB_L_mode = 0LS_L_mode = 0

HB_L_mode = 1LS_L_mode = 0

L_DBL_Pos

IF Environment not lit or not city: ADB_LitArea=0 AND Night condition: ADB_AmbientLight = 1 AND Automatic HB activated: SBEnable = 1 AND Camera vision OK : ADB_VisionStatus = 1 AND Reverse gear not engaged: ReverseGear =0 AND Engine Running: EngRunStatus = 1 or 2 AND ECU powered: (BoardActStatus = 5 OR BoardActStatus = 6) AND The speed FiltVehSpeed is inside the hysteresis enable area (see figure \"Hysteris for function activation/deativation according to vehicle speed\") AND The Steering wheel FiltStWhAngle is inside the valid range (see requirement D045049) AND The ADB function is configured ADB_FuncConf =1 The board is properly supplied SystemPowerMode=2 No failure on vehicle CAN: CAN_FAIL 1 AND No failure on Camera CAN : CameraStatusFail = 0 AND CameraObjectFail = 0THEN LS_activation_condition = 1ELSE LS_activation_condition = 0

HB_mode == 1

(HiBeamatic_active == 0&&HighBeamStatus==0&&LS_L_enable ==1

IF HiBeamatic == 1 AND LS_activation_condition==1 HiBeamatic_active = 1ELSE HiBeamatic_active = 0END

The outputs LS_L_enable =1 and LS_R_enable=1 shall be set ‘ON’ IF : LS_activation_condition == 1 AND LS_HALeft_Valid / LS_HARight_Valid ==1 AND the angles (LS_HALeft_Saturated and LS_HARight_Saturated) are inside the indexed validity zone ELSE LS_L_enable =0 / LS_R_enable=0END

HighBeamStatus

IF Cam_ObjNum == 0 HiBeamatic = 1ELSE HiBeamatic = 0END

Left_SB_Angle

ADB_City

HB_mode

HB_mode == 0&&LS_L_mode == 0

L_DBL_Angle_SetP

ADBLeftprState

L_DBL_active = 0L_LS_active = 0

IF LS_mode is active: L_LS_active == 1 L_DBL_Pos = Left_SB_AngleELSEIF L_DBL_active == 1 L_DBL_Pos = L_DBL_Angle_SetPELSE L_DBL_Pos = 0END