FMU30操作页面
2025-03-10 15:56:16 0 举报AI智能生成
FMU30液位仪直观的操作界面
作者其他创作
大纲/内容
00 Basic Setup (基本设置)
002 Tank Shape (罐体形状)
- Dome ceiling (拱顶罐)
- Horizontal cylinder (卧罐)
- Bypass (旁通管)
- Stilling well (导波管)
- Flat ceiling (平顶罐)
- Sphere (球罐)
- No ceiling (敞口罐)
003 Medium Property (介质属性)
- Liquid (液体)
- Solid <4mm (固体<4mm)
- Solid >4mm (固体>4mm)
- Unknown (未知)
004 Process Condition (过程条件)
- Standard liquid (标准液体)
- Calm surface (平静液面)
- Turbulent surface (扰动液面)
- Add agitator (附加搅拌器)
- Fast change (快速变化)
- Standard solid (标准固体)
- Solid dusty (固体粉尘)
- Conveyor belt (传输带)
- Test: No filter (测试:无滤波器)
005 Empty Calibration (空标)
- Distance membrane to min. level (膜片至最低液位距离)
059 Blocking Distance (盲区距离)
006 Full Calibration (满标)
- Span (满量程)
008 Dist./Meas. Value (距离/测量值)
- Displayed values: (显示值)
- Distance membrane to level (膜片至物位距离)
- Measured value (测量值)
051 Check Distance (检查距离)
- Distance unknown (距离未知)
- Distance too small (距离过小)
- Distance too big (距离过大)
- Manual (手动)
- Distance = OK (距离正常)
052 Range of Mapping (抑制范围)
- Common (常规)
- Extended mapping (扩展抑制)
053 Start Blocking (启动抑制)
- Off (关)
- On (开)
01 Safety Settings (安全设置)
010 Output on Alarm (报警输出)
012 Output Echo Loss (输出回波丢失)
013 Rampe %span/min (斜率设置)
- Unit: %span/min (单位:%满量程/min)
014 Delay Time (延迟时间)
- Max. 4000s on echo loss (回波丢失时最大4000秒)
- Default: 60s (默认60秒)
03 Temperature (温度设置)
030 Measured Temp. (温度测量值)
031 Max. Temp. Limit (最大温度限定值)
032 Max. Meas. Temp. (最大温度测量值)
033 React. High Temp. (高温反应)
- Warning (警告)
- Alarm (报警)
034 Defect Temp. Sensor (温度传感器故障)
- Alarm (报警)
- Warning (警告)
04 Linearisation (线性化)
041 Linearisation (线性化类型)
042 Customer Unit (用户单位设置)
043 Linearisation Table No. (线性化表号)
044 Level Linearisation (物位线性化)
045 Volume Linearisation (体积线性化)
046 Max. Scale (最大比例)
047 Diameter Vessel (容器直径)
05 Extended Calibr. (扩展标定)
050 Selection (选择)
051 Check Distance (检查距离)
052 Range of Mapping (抑制范围)
053 Start Blocking (启动抑制)
054 Pres. Blocking Distance (预设置抑制距离)
055 Cust. Tank Blocking (用户自定义罐体抑制)
056 Echo Quality (回波质量)
057 Offset (偏置量)
058 Output Damping (输出阻尼时间)
- Default: 2s (默认2秒)
059 Blocking Distance (盲区距离)
06 Output (输出设置)
062 Low Output Limit (低电流限定值)
- On/Off (开/关)
063 Current Output Mode (电流输出模式)
064 Fixed Current Value (固定电流值)
065 Simulation (仿真)
- Sim. Level (仿真物位)
- Sim. Volume (仿真体积)
- Sim. Current (仿真电流)
068 4mA Value (4mA值)
069 20mA Value (20mA值)
0E Envelope Curve (包络线设置)
0E1 Plot Settings (显示模式)
- Envelope curve (包络线)
- Env. curve + FAC (包络线+FAC)
- Env. curve + cust. map (包络线+用户自定义抑制)
0E2 Recording Curve (记录曲线)
- Single curve (单次包络线)
- Cyclic (循环包络线)
09 Display (显示设置)
093 Back to Home (返回主界面时间)
- Default: 100s (默认100秒)
094 Format Display (显示格式)
- Decimal (小数点)
- 1/16" (1/16英寸)
095 No. of Decimals (小数点位数)
- x
- x.x
- x.xx
- x.xxx
096 Sep. Character (小数点分隔符)
- Period (点号)
- Comma (逗号)
0A Diagnostics (诊断设置)
0A0 Present Error (当前错误)
0A1 Previous Error (前一条错误)
0A2 Clear Error (清除错误)
0A3 Reset (复位)
0A4 Unlock Parameter (解锁参数)
0C System Parameters (系统参数)
0C0 Tag No. (位号设置)
0C2 Protocol + SW-No. (协议+软件版本号)
0C4 Serial No. (序列号)
0C5 Distance Unit (距离单位)
0C6 Temperature Unit (温度单位)
service（服务）
0 条评论
下一页
